SGI Octane III Guía de usuario Pagina 17
- Pagina / 78
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Quick Setup Procedures
007-5630-001 5
System Connections and Power On
Once you have located the system in its operating environment, use the following steps and
illustrations to connect to monitor/keyboard/mouse, Ethernet, power and optional components:
1. Connect the keyboard and mouse to USB-N-A connectors on the rear of the enclosure, see
Figure 1-2. If you are using a workstation with two independent “heads” (a second internal
tray), connect the second keyboard and mouse to USB-N-B connectors.
2. Connect your monitor(s) to the DVI-N-A (and/or optionally DVI-N-B) video connector(s) on
the rear panel. See Table 1-1 on page 9 for more information on video/option connectors.
3. Plug a Cat-5 or equivalent Ethernet cable to GIGE-0-A on the rear panel of the system and
connect it to your local area network (LAN) as applicable.
4. If you have ordered an optional external DVD-RW drive, connect it to the remaining
USB-N-A plug on the rear of the system. Power-up the external drive after you have
successfully booted the Octane III. Remember that if you have a system using only the
primary tray (A), then only connectors from the USB-N-A side will work.
Figure 1-2 Octane III Deskside Workstation Rear Panel Connectors
5. With the enable power switch in the off (0) position, connect each of the power cables from
the power supply connectors on the rear of the system to approved wall plug outlets near the
work area. Note that the enable power switch is located between the two power plugs.
6. Push the enable power switch to the on (1) position to start the system, see Figure 1-3 on
page 6.
USB-2-A USB-2-B
VGA-B
SERIAL-B
GIGE-0-A
GIGE-0-B
GIGE-1-A GIGE-1-B
DVI-3-A DVI-3-B
Enable
p
ower switch
USB ports DVI ports
Serial
ports
Ethernet
ports
DVI-2-A DVI-2-B
DVI-1-A DVI-1-B
DVI-0-A DVI-0-B
SERIAL-A
VGA-A
USB-1-A
USB-1-B
USB-0-A USB-0-B
3D-A
3D-B
VGA
port
VGA
port
Stereo-sync
ports
- III Deskside Workstation 1
- System User’s Guide 1
- Record of Revision 3
- 007-5630-001 vii 7
- 007-5630-001 ix 9
- Contents 10
- List of Figures 11
- 1. Introduction and Overview 13
- Quick Setup Procedures 14
- 007-5630-001 3 15
- Choosing a Site 16
- 007-5630-001 5 17
- 6 007-5630-001 18
- 1: Introduction and Overview 18
- Power-On Problems 19
- System Overview 20
- I/O Panel Overview 21
- Physical Specifications 22
- System Power Supplies 22
- 007-5630-001 11 23
- 12 007-5630-001 24
- Nodeboard Features 25
- Serial ATA 26
- PCI Expansion Slots 26
- Optional Ethernet Ports 26
- Other Features 26
- InfiniBand 27
- 16 007-5630-001 28
- 007-5630-001 17 29
- Troubleshooting the System 30
- System Fan Failure 32
- Rear I/O Connectors 33
- USB Type A Connector 34
- VGA Video Interface 35
- RJ-45 (Ethernet) Connectors 36
- DB9 Serial Connector 37
- DVI-I Video/Monitor Port 38
- Stereo-Sync Connector 39
- 4. BIOS Information 41
- Starting the Setup Utility 42
- Main Setup 42
- System Time/System Update 43
- System Board 43
- Advanced Setup Configurations 44
- Boot Features 45
- Power Configuration 46
- Processor and Clock Options 47
- 36 007-5630-001 48
- 4: BIOS Information 48
- 007-5630-001 37 49
- Advanced Chipset Control 50
- 007-5630-001 39 51
- North Bridge Configuration 52
- SouthBridge Configuration 53
- 42 007-5630-001 54
- IDE and SATA Configuration 55
- 44 007-5630-001 56
- 007-5630-001 45 57
- PCI/PnP Configuration 58
- Remote Access Configuration 59
- 48 007-5630-001 60
- Hardware Health Monitor 61
- 50 007-5630-001 62
- ACPI Configuration 63
- Trusted Computing 64
- IPMI Configuration 65
- View BMC System Event Log 65
- Set LAN Configuration 66
- IP Address Configuration 66
- MAC Address Configuration 67
- Subnet Mask Configuration 67
- SEL PEF Configuration 68
- DMI Event Log 69
- Security Settings 70
- Boot Configuration 71
- Boot Device Priority 72
- Exit Options 73
- Save Changes and Exit 74
- Discard Changes and Exit 74
- BIOS Error Beep Codes 75
- BIOS Error Beep Code List 76
- A. Technical Specifications 77
- Environmental Specifications 78
Relacionado con productos y manuales para Servidores SGI Octane III
Servidores SGI InfiniteStorage 3500 Guía de usuario
(106 paginas)
(106 paginas)
Servidores SGI Altix XE210 Guía de usuario
(170 paginas)
(170 paginas)
Servidores SGI Altix XE340 Guía de usuario
(70 paginas)
(70 paginas)
Servidores SGI Origin 3900 Guía de usuario
(144 paginas)
(144 paginas)
Servidores SGI Rackable C1000 Guía de usuario
(30 paginas)
(30 paginas)
Servidores SGI UV 2000 Guía de usuario
(110 paginas)
(110 paginas)
Servidores SGI Rackable C2005 Family Guía de usuario
(46 paginas)
(46 paginas)
Servidores SGI Altix XE210 Guía de usuario
(44 paginas)
(44 paginas)
Servidores SGI ISS3500 Manual de usuario
(93 paginas)
(93 paginas)
Servidores SGI ISS3124-RP2 Manual de usuario
(28 paginas)
(28 paginas)
Servidores SGI C1110-RP6 Manual de usuario
(30 paginas)
(30 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.856 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales