SGI Ethernet Card Especificaciones Pagina 86
- Pagina / 154
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
SCPI Command Operation SG Series Programming
6-24 M550129-03 Rev G
Command Description
SCPI
:TERM
<NRf>
Sets the return string terminators to be used by the device. Factory
set to 3. The valid range is 1-4. Values indicate the following
terminator(s):
1 = 0x0d only (CR), 2 = 0x0a only (LF), 3 = 0x0d 0x0a (CR LF), 4 =
0x0a 0x0d (LF CR)
N
:TERM?
Returns the string terminators to be used by the device.
N
:VERsion?
Returns a numeric value corresponding to the SCPI version number
for which the instrument complies. The response is in the format
YYYY.V where the Y’s represent the year and V represents the
approved version number for that year (e.g., 1995.0)
C
Table 6-5. System Fault Registers
Bit Position Bit Weight Fault1–8 Fault9–16 Fault17–24 Fault25–31
7 128 Channel 1 not used not used not used
6 64 not used not used not used not used
5 32 not used not used not used not used
4 16 not used not used not used not used
3 8 not used not used not used not used
2 4 not used not used not used not used
1 2 not used not used not used not used
0 1 not used not used not used not used
The SYStem:FAULt? query returns 4 numeric values separated by commas.
Each value is the decimal equivalent of the total bit weights for that System Fault
Register as described in the table above.
- SG Series IEEE 1
- 488.2/RS232 and 1
- Ethernet Options 1
- CONTENTS 5
- GPIB) 7-5 8
- OVERVIEW 11
- M550129-03 Rev G 12
- IEEE 488.2 GPIB/RS232 13
- FEATURES, FUNCTIONS 13
- AND SPECIFICATIONS 13
- READBACK FUNCTIONS 14
- SPECIFICATIONS 14
- IEEE 488.2 GPIB/ RS232 15
- CONFIGURATIONS 15
- AND REMOTE PROGRAMMING 15
- 3-2 M550129-03 Rev G 16
- RS232 SETUP PROCEDURE 17
- 3-4 M550129-03 Rev G 18
- Configuration Switch 19
- Remote/Local Selection 20
- Shield Ground 22
- Address Selection 22
- REMOTE PROGRAMMING VIA RS232 23
- ETHERNET INTERFACE 25
- FEATURES, FUNCTIONS AND 25
- FEATURES AND FUNCTIONS 26
- Programming Resolution 28
- Programming Accuracy 28
- Readback Resolution 29
- Readback Accuracy 29
- ETHERNET CONFIGURATION 31
- AND REMOTE PROGRAMMING 31
- ETHERNET SETUP PROCEDURE 33
- Network Setup Using DHCP 34
- Network Setup Using Auto-IP 35
- 5-6 M550129-03 Rev G 36
- ENTER key a couple of times 37
- BACKSPACE or 37
- DELETE keys 37
- EXTERNAL USER CONTROL SIGNAL 40
- CONNECTOR 40
- 5-12 M550129-03 Rev G 42
- ETHERNET 43
- ETHERNET WEB PAGES, OVERVIEW 44
- M550129-03 Rev G 5-15 45
- Figure 5-11. Login Window 45
- 5.5.1 HOME 46
- IP CONFIGURATION 47
- 5-18 M550129-03 Rev G 48
- SETTINGS 51
- 5-22 M550129-03 Rev G 52
- SCPI COMMAND SECTION: 53
- 5.5.4 STATUS 54
- 5.5.5 POWER 56
- PRESETS 58
- SECURITY 60
- ADD NEW USER 61
- EDIT EXISTING USER 62
- AND SCPI COMMAND OPERATION 63
- Register 65
- Registers 67
- Error/Event Queue 67
- CONFORMANCE INFORMATION 70
- Queries 71
- Conventions 71
- IEEE 488.2 COMMON COMMAND 72
- SUBSYSTEM 72
- M550129-03 Rev G 6-11 73
- Command Description 73
- SOURCE SCPI Command Summary 74
- 6-14 M550129-03 Rev G 76
- Command Description 76
- M550129-03 Rev G 6-15 77
- RAMP FUNCTION 78
- MEASURE SCPI Command Summary 79
- OUTPUT SCPI Command Summary 80
- STATUS SCPI Command Summary 81
- SYSTEM SCPI Command Summary 83
- TRIGGER SCPI Command Summary 88
- (applies to Ethernet only) 90
- 6-30 M550129-03 Rev G 92
- M550129-03 Rev G 6-31 93
- SGI-UNIQUE COMMANDS 94
- PROGRAM SCPI COMMAND SUMMARY 96
- OMMAND REFERENCE 97
- 6-36 M550129-03 Rev G 98
- M550129-03 Rev G 6-37 99
- 6-38 M550129-03 Rev G 100
- Command Description SCPI 100
- M550129-03 Rev G 6-39 101
- 6-40 M550129-03 Rev G 102
- VI Mode Example 104
- OVP Setup Example 104
- Trigger Example 105
- Hardware Trigger Example 106
- Ramp V Example 106
- Ramp I Example 106
- Ramp V Example 2 107
- Power On INIT Example 107
- “Charge” 117
- “Discharge” 117
- 6-60 M550129-03 Rev G 122
- CALIBRATION 123
- SETUP FOR CALIBRATION 124
- (ETHERNET) 125
- 7-4 M550129-03 Rev G 126
- (ETHERNET, GPIB) 127
- CALIBRATION (ETHERNET, GPIB) 128
- 7-8 M550129-03 Rev G 130
- 7-10 M550129-03 Rev G 132
- ANALOG PROGRAM ADJUSTMENT 133
- 7-12 M550129-03 Rev G 134
- Adjustment for Current Mode 136
- Adjustment for Voltage Mode 137
- 7-16 M550129-03 Rev G 138
- M550129-03 Rev G 7-17 139
- SCPI STATUS IMPLEMENTATION 141
- Index-1 145
- FAULT output signal, 5-11 145
- FOLDBACK output signal, 5-11 145
- SG Series Programming Index 147
- Index-3 147
- SAFETY SYMBOLS 151
Relacionado con productos y manuales para Redes SGI Ethernet Card
Redes SGI Ethernet Card Guía de usuario
(41 paginas)
(41 paginas)
Redes SGI network adapter Guía de usuario
(72 paginas)
(72 paginas)
Redes SGI Ethernet Card Guía de instalación
(28 paginas)
(28 paginas)
Redes SGI network adapter Guía de usuario
(30 paginas)
(30 paginas)
Redes SGI Ethernet Card Guía de usuario
(42 paginas)
(42 paginas)
Redes SGI network adapter Guía de usuario
(34 paginas)
(34 paginas)
Redes SGI Ethernet Card Guía de usuario
(52 paginas)
(52 paginas)
Redes SGI Ethernet Card Guía de usuario
(36 paginas)
(36 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales