SGI Rackable C2112-4G3 Guía de usuario Pagina 29
- Pagina / 104
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Server Chassis Features
007-5759-001 5
Server Chassis Features
The following subsections provide a general outline of the main features of the SGI Rackable
C2112-4G3 server chassis.
System Power
The Rackable C2112-4G3 2U server chassis features uses two power supplies accessible at the
rear of the system. Specific configurations of the server offer a power redundancy feature which
allows you to replace a failed power supply without shutting down the system. No tools are
required to remove and replace a power supply. Note that each power supply is rated at 80 Plus
Gold certification.
Serial ATA Drive Subsystems
The server chassis optionally supports up to twelve 3 Gb/s Serial ATA drives (three for each
serverboard). The SATA drives are all non-RAID (Jbod) units and are connected to a backplane
that provides power and control. Note that these drives do not support the hot-swap capability of
RAID drives.
Front Control Panels
There are four separate front control panels (one for each of the serverboards). Each C2112-4G3
serverboard control panel provides you with system monitoring and control LEDs that indicate
system power, HDD activity, network activity, system overheat and power supply failure. A main
power button and a system reset button are also included.
Serverboard
The C2112-4G3 server chassis is an ATX form factor chassis designed to be used in a 2U
rackmount configuration. Each serverboard provides one low-profile PCIe expansion slot, one
COM port, a VGA port, two USB 2.0 ports and two Gigabit LAN ports. A dedicated RJ-45 IPMI
LAN port is also supported. Figure 1-2 on page 6 shows a general block diagram of an individual
C2112-4G3 processor board and I/O chipset. Low-profile PCIe cards must be less than 5.9 inches
(15 cm) in length.
- Rackable 1
- C2112-4G3 1
- System User’s Guide 1
- Record of Revision 3
- About This Guide 5
- Related Publications 7
- Conventions 8
- Product Support 8
- Reader Comments 9
- Contents 11
- 007-5759-001 xiii 13
- 007-5759-001 xv 15
- 007-5759-001 xvii 17
- 007-5759-001 xix 19
- 007-5759-001 xxi 21
- 007-5759-001 xxiii 23
- 1. Introduction 25
- 2 007-5759-001 26
- 1: Introduction 26
- Server Board Features 27
- PCI Expansion Slots 28
- Onboard Controllers/Ports 28
- Onboard Graphics Controller 28
- Optional InfiniBand Connector 28
- Other Features 28
- Server Chassis Features 29
- DDR2 SDRAM 30
- Cooling System 31
- 2. Server Installation 33
- Warnings and Precautions 34
- Rack Mounting Considerations 35
- Circuit Overloading 36
- Reliable Ground 36
- Outer Rack Rails 37
- Install the Inner Rails 38
- Install the Server in a Rack 39
- Check the Node Board Setup 40
- Check the CPUs (processors) 41
- Check the System Memory 41
- Install Expansion PCIe Cards 42
- Check the Drive Bay Setup 42
- 3. System Interface 43
- Control Panel LEDs 44
- Drive Carrier LEDs 45
- 22 007-5759-001 46
- 3: System Interface 46
- 4. System Safety 47
- Serverboard Battery 48
- Optional CD/DVD-ROM Laser 48
- General Safety Precautions 49
- ESD Precautions 49
- 26 007-5759-001 50
- 4: System Safety 50
- Handling the Node Board 51
- Unpacking 52
- Connecting the Control Panel 52
- Serverboard I/O Ports 53
- Serverboard Details 54
- Serverboard Health Monitoring 55
- ACPI Features 55
- Mellonox 56
- Connect-X 56
- Installing Memory 57
- Memory DIMM Layout 58
- 007-5759-001 35 59
- SLOT1:PCI-E 2.0 x16 60
- InfiniBand 60
- 007-5759-001 39 63
- Drive location 0 64
- Drive location 1 64
- Drive location 2 64
- Drive Configurations 65
- PCIe Expansion Cards 66
- 007-5759-001 43 67
- Memory Errors 68
- Chassis Service Information 69
- Control Panel 70
- System Fans 70
- 007-5759-001 47 71
- System Fan Failure 72
- Replacing System Fans 72
- 007-5759-001 49 73
- Accessing the Drive Bays 74
- Disk Drive Installation 74
- 007-5759-001 51 75
- Hard Drive Backplane 76
- Power Supply 77
- Power Supply Failure 77
- Installing a New Power Supply 78
- PCIe Card Installation Steps 79
- 56 007-5759-001 80
- Starting BIOS Setup Utility 81
- Starting the Setup Utility 82
- Main Menu 83
- Advanced Setup Configurations 84
- 007-5759-001 61 85
- 62 007-5759-001 86
- Memory Configuration 87
- ECC Configuration 88
- IDE Configuration 89
- SATA IDE Combined Mode 90
- PATA Channel Configuration 90
- LBA/Large Mode 90
- Block (Multi-Sector Transfer) 90
- PIO Mode 90
- PCI/PNP Settings Menu 91
- 68 007-5759-001 92
- SuperIO Device Configuration 93
- Remote Access Configuration 94
- Hardware Health Configuration 95
- ACPI Configuration 95
- 72 007-5759-001 96
- Event Log Configuration 97
- Security Menu 98
- Boot Menu 98
- Exit Menu 99
- Load Optimal Defaults 100
- Load Fail-Safe Defaults 100
- A. BIOS Error Codes 101
- Operating Environment 103
- Regulatory Compliance 103
© 2020, manymanuals.es. Todos los derechos reservados | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales