SGI Rackable C2112-4G3 Guía de usuario Pagina 77
- Pagina / 104
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Drive Bay Installation/Removal
007-5759-001 53
Power Supply
The server uses a power supply system consisting of two replaceable power modules. Each power
supply module has an auto-switching capability, which enables it to automatically sense and
operate at a 100V - 240V input voltage.
Power Supply Failure
In most configurations of the C2112-4G3 server your system has power supply redundancy. If
either of the two power supply modules fail, the other module will take the full load and allow the
system to continue operation without interruption. The PWR Fail LED will illuminate and remain
on until the failed unit has been replaced.
Removing/Replacing the Power Supply
If the server is continuing to work with only the second power supply, you do not need to shut
down the system to replace the failed unit. In most configurations, the second power supply
module will keep the system up and running while you obtain a replacement. Always replace a
failed power supply with the same model as soon as possible.
Removing the Power Supply
1. First unplug the AC power cord from the failed power supply module.
2. Depress the locking tab on the power supply module.
3. Pull it straight out using the rounded handle, see Figure 6-5 on page 54 for an example.
- Rackable 1
- C2112-4G3 1
- System User’s Guide 1
- Record of Revision 3
- About This Guide 5
- Related Publications 7
- Conventions 8
- Product Support 8
- Reader Comments 9
- Contents 11
- 007-5759-001 xiii 13
- 007-5759-001 xv 15
- 007-5759-001 xvii 17
- 007-5759-001 xix 19
- 007-5759-001 xxi 21
- 007-5759-001 xxiii 23
- 1. Introduction 25
- 2 007-5759-001 26
- 1: Introduction 26
- Server Board Features 27
- PCI Expansion Slots 28
- Onboard Controllers/Ports 28
- Onboard Graphics Controller 28
- Optional InfiniBand Connector 28
- Other Features 28
- Server Chassis Features 29
- DDR2 SDRAM 30
- Cooling System 31
- 2. Server Installation 33
- Warnings and Precautions 34
- Rack Mounting Considerations 35
- Circuit Overloading 36
- Reliable Ground 36
- Outer Rack Rails 37
- Install the Inner Rails 38
- Install the Server in a Rack 39
- Check the Node Board Setup 40
- Check the CPUs (processors) 41
- Check the System Memory 41
- Install Expansion PCIe Cards 42
- Check the Drive Bay Setup 42
- 3. System Interface 43
- Control Panel LEDs 44
- Drive Carrier LEDs 45
- 22 007-5759-001 46
- 3: System Interface 46
- 4. System Safety 47
- Serverboard Battery 48
- Optional CD/DVD-ROM Laser 48
- General Safety Precautions 49
- ESD Precautions 49
- 26 007-5759-001 50
- 4: System Safety 50
- Handling the Node Board 51
- Unpacking 52
- Connecting the Control Panel 52
- Serverboard I/O Ports 53
- Serverboard Details 54
- Serverboard Health Monitoring 55
- ACPI Features 55
- Mellonox 56
- Connect-X 56
- Installing Memory 57
- Memory DIMM Layout 58
- 007-5759-001 35 59
- SLOT1:PCI-E 2.0 x16 60
- InfiniBand 60
- 007-5759-001 39 63
- Drive location 0 64
- Drive location 1 64
- Drive location 2 64
- Drive Configurations 65
- PCIe Expansion Cards 66
- 007-5759-001 43 67
- Memory Errors 68
- Chassis Service Information 69
- Control Panel 70
- System Fans 70
- 007-5759-001 47 71
- System Fan Failure 72
- Replacing System Fans 72
- 007-5759-001 49 73
- Accessing the Drive Bays 74
- Disk Drive Installation 74
- 007-5759-001 51 75
- Hard Drive Backplane 76
- Power Supply 77
- Power Supply Failure 77
- Installing a New Power Supply 78
- PCIe Card Installation Steps 79
- 56 007-5759-001 80
- Starting BIOS Setup Utility 81
- Starting the Setup Utility 82
- Main Menu 83
- Advanced Setup Configurations 84
- 007-5759-001 61 85
- 62 007-5759-001 86
- Memory Configuration 87
- ECC Configuration 88
- IDE Configuration 89
- SATA IDE Combined Mode 90
- PATA Channel Configuration 90
- LBA/Large Mode 90
- Block (Multi-Sector Transfer) 90
- PIO Mode 90
- PCI/PNP Settings Menu 91
- 68 007-5759-001 92
- SuperIO Device Configuration 93
- Remote Access Configuration 94
- Hardware Health Configuration 95
- ACPI Configuration 95
- 72 007-5759-001 96
- Event Log Configuration 97
- Security Menu 98
- Boot Menu 98
- Exit Menu 99
- Load Optimal Defaults 100
- Load Fail-Safe Defaults 100
- A. BIOS Error Codes 101
- Operating Environment 103
- Regulatory Compliance 103
© 2020, manymanuals.es. Todos los derechos reservados | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales