SGI Rackable C2112-4G3 Guía de usuario Pagina 90
- Pagina / 104
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
66 007-5759-001
7: BIOS
SATA IDE Combined Mode
This setting allows you to Enable or Disable the SATA IDE combined mode.
PATA Channel Configuration
This allows you to set PATA channel configuration. Options include SATA as Primary or SATA
as secondary.
Primary/Secondary/Third/Fourth IDE Master/Slave
LBA/Large Mode
LBA (Logical Block Addressing) is a method of addressing data on a disk drive. The options are
Disabled and Auto.
Block (Multi-Sector Transfer)
Block mode boosts IDE drive performance by increasing the amount of data transferred. Only 512
bytes of data can be transferred per interrupt if block mode is not used. Block mode allows
transfers of up to 64 KB per interrupt. Select "Disabled" to allow the data to be transferred from
and to the device one sector at a time. Select "Auto" to allows the data transfer from and to the
device occur multiple sectors at a time if the device supports it. The options are Auto and
Disabled.
PIO Mode
PIO (Programmable I/O) mode programs timing cycles between the IDE drive and the
programmable IDE controller. As the PIO mode increases, the cycle time decreases.
The options are Auto, 0, 1, 2, 3, and 4. Select Auto to allow BIOS to auto detect the PIO mode.
Use this value if the IDE disk drive support cannot be determined. Select 0 to allow BIOS to use
PIO mode 0, which has a data transfer rate of 3.3 MBs. Select 1 to allow BIOS to use PIO mode
1, which has a data transfer rate of 5.2 MBs. Select 2 to allow BIOS to use PIO mode 2, which has
a data transfer rate of 8.3 MBs. Select 3 to allow BIOS to use PIO mode 3, which has a data
transfer rate of 11.1 MBs. Select 4 to allow BIOS to use PIO mode 4, which has a data transfer
rate of 16.6 MBs. This setting generally works with all hard disk drives manufactured after 1999.
For other disk drives, such as IDE CD-ROM drives, check the specifications of the drive.
- Rackable 1
- C2112-4G3 1
- System User’s Guide 1
- Record of Revision 3
- About This Guide 5
- Related Publications 7
- Conventions 8
- Product Support 8
- Reader Comments 9
- Contents 11
- 007-5759-001 xiii 13
- 007-5759-001 xv 15
- 007-5759-001 xvii 17
- 007-5759-001 xix 19
- 007-5759-001 xxi 21
- 007-5759-001 xxiii 23
- 1. Introduction 25
- 2 007-5759-001 26
- 1: Introduction 26
- Server Board Features 27
- PCI Expansion Slots 28
- Onboard Controllers/Ports 28
- Onboard Graphics Controller 28
- Optional InfiniBand Connector 28
- Other Features 28
- Server Chassis Features 29
- DDR2 SDRAM 30
- Cooling System 31
- 2. Server Installation 33
- Warnings and Precautions 34
- Rack Mounting Considerations 35
- Circuit Overloading 36
- Reliable Ground 36
- Outer Rack Rails 37
- Install the Inner Rails 38
- Install the Server in a Rack 39
- Check the Node Board Setup 40
- Check the CPUs (processors) 41
- Check the System Memory 41
- Install Expansion PCIe Cards 42
- Check the Drive Bay Setup 42
- 3. System Interface 43
- Control Panel LEDs 44
- Drive Carrier LEDs 45
- 22 007-5759-001 46
- 3: System Interface 46
- 4. System Safety 47
- Serverboard Battery 48
- Optional CD/DVD-ROM Laser 48
- General Safety Precautions 49
- ESD Precautions 49
- 26 007-5759-001 50
- 4: System Safety 50
- Handling the Node Board 51
- Unpacking 52
- Connecting the Control Panel 52
- Serverboard I/O Ports 53
- Serverboard Details 54
- Serverboard Health Monitoring 55
- ACPI Features 55
- Mellonox 56
- Connect-X 56
- Installing Memory 57
- Memory DIMM Layout 58
- 007-5759-001 35 59
- SLOT1:PCI-E 2.0 x16 60
- InfiniBand 60
- 007-5759-001 39 63
- Drive location 0 64
- Drive location 1 64
- Drive location 2 64
- Drive Configurations 65
- PCIe Expansion Cards 66
- 007-5759-001 43 67
- Memory Errors 68
- Chassis Service Information 69
- Control Panel 70
- System Fans 70
- 007-5759-001 47 71
- System Fan Failure 72
- Replacing System Fans 72
- 007-5759-001 49 73
- Accessing the Drive Bays 74
- Disk Drive Installation 74
- 007-5759-001 51 75
- Hard Drive Backplane 76
- Power Supply 77
- Power Supply Failure 77
- Installing a New Power Supply 78
- PCIe Card Installation Steps 79
- 56 007-5759-001 80
- Starting BIOS Setup Utility 81
- Starting the Setup Utility 82
- Main Menu 83
- Advanced Setup Configurations 84
- 007-5759-001 61 85
- 62 007-5759-001 86
- Memory Configuration 87
- ECC Configuration 88
- IDE Configuration 89
- SATA IDE Combined Mode 90
- PATA Channel Configuration 90
- LBA/Large Mode 90
- Block (Multi-Sector Transfer) 90
- PIO Mode 90
- PCI/PNP Settings Menu 91
- 68 007-5759-001 92
- SuperIO Device Configuration 93
- Remote Access Configuration 94
- Hardware Health Configuration 95
- ACPI Configuration 95
- 72 007-5759-001 96
- Event Log Configuration 97
- Security Menu 98
- Boot Menu 98
- Exit Menu 99
- Load Optimal Defaults 100
- Load Fail-Safe Defaults 100
- A. BIOS Error Codes 101
- Operating Environment 103
- Regulatory Compliance 103
© 2020, manymanuals.es. Todos los derechos reservados | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales